<!-- Reviews -->
<div class="col-sm-12 col-md-8 col-lg-9 value content">
<div data-bv-show="reviews" data-bv-productId="370418">
<!--begin-bvseo-reviews-->
<!--begin-reviews-->
<div id="bvseo-reviewsSection">
<div class="bvseo-review" itemprop="review" itemscope itemtype="http://schema.org/Review" data-reviewid="119114080">
<span itemprop="reviewRating" itemscope itemtype="http://schema.org/Rating">
Rated <span itemprop="ratingValue">5</span> out of
<span itemprop="bestRating">5</span>
</span> by
<span itemprop="author">Richard IV</span> from
<span itemprop="name">Works well if sprayed from 8 inches plus</span>
<span itemprop="description">I used a tin of this to fill in the blemishes on a mountain bike frame. I'd sanded and primed already, but this just evens the surface out. I sprayed good solid coats on consecutive nights, and let it all go off for 72 hours before a final sanding (1200 grit W&D). Great surface to spray on - I used SPRAY-BIKE acrylic and it went on beautifully...</span>
<div class="bvseo-pubdate">Date published: 2020-03-21</div>
<meta itemprop="datePublished" content="2020-03-21" />
</div>
<div class="bvseo-review" itemprop="review" itemscope itemtype="http://schema.org/Review" data-reviewid="118912270">
<span itemprop="reviewRating" itemscope itemtype="http://schema.org/Rating">
Rated <span itemprop="ratingValue">5</span> out of
<span itemprop="bestRating">5</span>
</span> by
<span itemprop="author">Craggle427</span> from
<span itemprop="name">Does what it should</span>
<span itemprop="description">Bought this to prime and smooth out the surface of a component that had been bead blasted clean. Sprayed three coats onto it, sanded smooth and ready for top coat. Works very well but it takes some serious shaking to get the rattle ball in the can to start moving!</span>
<div class="bvseo-pubdate">Date published: 2020-03-11</div>
<meta itemprop="datePublished" content="2020-03-11" />
</div>
<div class="bvseo-review" itemprop="review" itemscope itemtype="http://schema.org/Review" data-reviewid="113675312">
<span itemprop="reviewRating" itemscope itemtype="http://schema.org/Rating">
Rated <span itemprop="ratingValue">5</span> out of
<span itemprop="bestRating">5</span>
</span> by
<span itemprop="author">rob8781</span> from
<span itemprop="name">Great product</span>
<span itemprop="description">Does exactly what is says on the tin, "designed to fill slight cracks and indentations".
Important: YOU HAVE TO SHAKE THE CAN HARD. If you don't it wont spray properly, took about 30 seconds before the agitator ball started to rattle, then shook foe a further 2 mins.
3 good coats leaves a nice thick finish that can be sanded flat 24 hours later.</span>
<div class="bvseo-pubdate">Date published: 2019-08-31</div>
<meta itemprop="datePublished" content="2019-08-31" />
</div>
<div class="bvseo-review" itemprop="review" itemscope itemtype="http://schema.org/Review" data-reviewid="113101551">
<span itemprop="reviewRating" itemscope itemtype="http://schema.org/Rating">
Rated <span itemprop="ratingValue">2</span> out of
<span itemprop="bestRating">5</span>
</span> by
<span itemprop="author">Lotsw</span> from
<span itemprop="name">Poor high build qualities</span>
<span itemprop="description">I applied 4 coats, following the instructions on the can. Next day, I started to flat it down using 2000 grit wet and dry sandpaper. The primer had a smooth surface and was easy to flat down, but it's high build quality was very poor. It hadn't done a good job of filling minor marks or scratches and the 4 coats were far too easy to flatten through, to my etch-primer underneath
Might as well not used it.</span>
<div class="bvseo-pubdate">Date published: 2019-08-08</div>
<meta itemprop="datePublished" content="2019-08-08" />
</div>
<div class="bvseo-review" itemprop="review" itemscope itemtype="http://schema.org/Review" data-reviewid="111431779">
<span itemprop="reviewRating" itemscope itemtype="http://schema.org/Rating">
Rated <span itemprop="ratingValue">5</span> out of
<span itemprop="bestRating">5</span>
</span> by
<span itemprop="author">Neilappeal2020</span> from
<span itemprop="name">You need to know what you're doing!</span>
<span itemprop="description">Used this many times. Latest project was front bumper. First give a good sanding with 300-600 grit wet/dry, fill anything with p38, resand and then spray with this primer. When dry, best leave 24hrs, look for tiny holes from stone chips etc. Sand the primer with 600 wet dry to make smooth. Wash properly and wipe with alcohol wipes. Respray again with this primer. This is where the high build effect comes in. Tiny holes less than half mm and other tiny imperfections get filled. Once dry, sand again with 600 wet dry. Should be perfect ready for paint. If not, give another coat or fill any other minor imperfections then decrease with alcohol wipes and then should be perfect ready for the colour coat. Remember, if metal is bare or shows through sanding use an etch primer first. If painting bare plastic use a plastic primer first. This is where people are going wrong in the other reviews with cracking and bubbling etc. I've used this on car body parts, motorcycle alloys and other things and I've been very happy. It's great if you know what you're doing. If you're not sure look on you tube.</span>
<div class="bvseo-pubdate">Date published: 2019-05-31</div>
<meta itemprop="datePublished" content="2019-05-31" />
</div>
</div>
<script type="text/javascript">
if (document.getElementById('bvseo-reviewsSection')) {
document.getElementById('bvseo-reviewsSection').style.display = 'none';
}
</script>
<!--end-reviews-->
<!--begin-pagination-->
<ul id="bvseo-paginationSection">
<li class="bvseo-paginationItem"><a class="bvseo-paginationLink" href="https://www.halfords.com/motoring/paints-and-body-repair/primer/halfords-high-build-primer-500ml-370418.html?bvstate=pg:2/ct:r">Halfords High Build Primer 500ml Reviews - page 2</a></li>
</ul>
<!--end-pagination-->
<ul id="BVSEO_meta" style="display:none!important">
<li data-bvseo="bvDateModified">y_2020, m_4, d_8, h_13</li>
<li data-bvseo="ps">bvseo_bulk, prod_bvrr, vn_bulk_3.0.5</li>
<li data-bvseo="cp">cp_1, bvpage1</li>
<li data-bvseo="co">co_hasreviews, tv_0, tr_20</li>
<li data-bvseo="cf">loc_en_GB, sid_370418, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]</li>
<li data-bvseo="diagnostics">clientName_halfords</li>
</ul>
<!--end-bvseo-reviews-->
<ul id="BVSEOSDK_meta" style="display: none !important;">
<li data-bvseo="sdk">bvseo_sdk, dw_cartridge, 18.2.0, p_sdk_3.2.0</li>
<li data-bvseo="sp_mt">CLOUD, getReviews, 10ms</li>
<li data-bvseo="ct_st">reviews, product</li>
</ul>
</div>
</div>
<!-- End Reviews -->
